Fitting and aftercare

Tackifier, pressure-sensitive adhesive or peel-and-stick: fixing second-hand tiles

Carpet tile tackifier vs adhesive comes down to one question: will anyone need to lift these tiles before the floor is replaced? Tackifier holds tiles against sliding but lets them come up, which is why it is the usual choice over access floors and for floors that will change soon. A pressure-sensitive adhesive holds more firmly and suits a floor meant to stay down. Peel-and-stick puts the adhesive on the tile or a tab before it reaches you. Whichever you pick, the tile has to be flat and clean first, and the manufacturer's installation guide for the range has the last word.

Three ways to fix a carpet tile
MethodHow it holdsLifting a tile laterUsually suits
TackifierHolds tiles against sliding while letting them liftMade to be lifted — the point of using itAccess floors, short lets, floors likely to change soon
Pressure-sensitive adhesiveA firmer hold, bonding as the tile is pressed downVaries by product; check how releasable it isLong-term floors that will not need lifting
Peel-and-stickAdhesive already applied, on the tile or on a tab, under a release filmDepends on the product and what it is stuck toSmall areas and quick jobs, where the product suits the tile

Three fixing methods and what each costs per square metre

Most advice on how to fix carpet tiles assumes new stock from a fresh box. Stock that has spent time in storage changes the starting point, but not the choice between the three routes, which turns on how hard you want the floor to hold and how easily you want it to let go.

Tackifier is applied to the subfloor and left to become tacky before the tiles go down. It stops tiles sliding and creeping without bonding them for good, so a single tile can be lifted and put back. Pressure-sensitive adhesive also goes on the floor, and bonds as the tile is pressed into it. Products differ in how firmly they hold and how readily they release, so read the data sheet rather than assuming. Peel-and-stick arrives with the adhesive already on it — on the back of the tile, or on tabs that join tiles at the corners — protected by a film you peel off as you lay.

Nothing on this site prices these products, and we are not going to guess: prices move with the supplier and the quantity. What we can give you is the sum, so that the quotes you get compare like with like — the same approach the guide to weighing surplus against new tiles on a fit-out takes for the tiles themselves.

Working out the cost per square metre

  1. Product per m² = price of one tub, can or pack ÷ the square metres it covers. The coverage is on the data sheet, and it changes with the subfloor.
  2. Preparation per m² = any primer or cleaning the subfloor needs, worked out the same way.
  3. Laying time — including any drying time before tiles can go down, which is time on site whether or not anyone is laying.
  4. Lifting later — the cost of getting a tile up again, which is close to nothing on tackifier and can be a damaged tile on a firmer bond.

Multiply the total per m² by the area you are fixing, not the area of tile you bought — the measuring guide keeps those two numbers apart.

The fourth line is the one that decides most jobs. For a short-term let or a refit between tenants, where the floor may come up again within a few years, a cheap bond that is expensive to undo is not cheap. For an office floor expected to stay down for ten years, the cost of lifting matters less than a hold that keeps tiles still under a decade of chair castors.

Access floors and raised voids: why tackifier usually wins

An access floor exists so that someone can lift a panel and reach the cabling or services beneath it. Every tile laid over it has to come up with the panel, or come off the panel, without a fight. That is exactly what tackifier is made for, and why it is usually the choice for raised floors.

Check the tile size against the panel size before you lay. Where the two differ, tiles bridge the panel joints, and lifting one panel means lifting every tile that crosses its edges. A fixing that lets go cleanly keeps that a few minutes' work; a firm bond turns it into damaged tiles and a patch that does not match.

Peel and stick carpet tiles on access floor panels need the same test. How cleanly a factory-applied adhesive releases from a panel is a property of that product, not of peel-and-stick in general, so read the data sheet before assuming it will come away when someone needs the void.

Priming dusty or older tile backing before you stick it down

Stock that has stood for two years in a store has had two years to collect dust, and dust is one of the plainest reasons a fixing does not take. Adhesive bonds to whatever it touches first, and if that is a film of dust, the tile is stuck to the dust rather than the floor.

Priming is normally done to the subfloor, not the tile: a primer seals a porous or dusty floor so the adhesive grips it rather than soaking in. For the tile itself, the job is cleaning. Brush or vacuum the backing of each tile before it goes down, and lay a few as a test before committing a whole floor. Whether a particular backing can or should be primed is a question for the adhesive maker, and their data sheet will say.

Genuinely second-hand tiles — lifted from a floor, rather than surplus that was never laid — bring a different problem: old adhesive on the back. Residue left from a previous fixing can stop a new one taking, and the two products may not be compatible. Ask what the tiles were fixed with before, and clean off what you can. Most stock on Carpet Unboxed is surplus that has never been down, which is what boxed and unused means on a listing, so the backing has nothing on it but whatever storage left.

Common failures and how to spot them early

Most of these show early if you look for them, which is why a test area is worth its morning. These are the ones to watch for.

Adhesive that never grabs. The tile sits on the floor but lifts with no resistance. The usual causes are dust on the backing or the floor, and tiles laid before the adhesive has reached the tack its data sheet describes. Spot it by lifting a tile from your test area the next day: a good bond leaves you working to get it up.

Tiles that creep at the edges. Joints open, tiles ride over one another, and gaps appear where the floor meets a wall. On surplus the cause is often a tile that was not flat to begin with. A tile that has taken a set from the way it was stored will try to return to it, and no fixing holds that for long. Tiles from a cold store usually settle if left flat in a heated room for 24 to 48 hours before laying; any that still rock after that should go to cuts, not the middle of the floor.

Tackifier that lifts in a warm server room. Rooms that run warm all year, around comms cabinets or server racks, ask more of a releasable fixing than an ordinary office does. Tiles start moving underfoot and corners lift near the equipment first. Before you fix a room like that, check the temperature range on the product's data sheet, and ask the manufacturer what they recommend for it.

Backing that will not sit down. Some failures belong to the tile rather than the fixing. A bitumen backing that has cracked in the cold, a PVC backing gone stiff, or a cushion backing crushed where something heavy stood on it will not bond evenly whatever you use. The inspection checklist covers how to catch these before you buy, which is cheaper than catching them on the floor.

Sourcing tiles for a job? See surplus carpet tiles available now, or request a quote and tell us what floor they are going on.

Questions

Fixing questions we hear most.

Where do I find which fixing a tile was made for?

On the manufacturer's installation guide for the range. Take the full product code from the box label and look it up; the guide names the adhesives the tile was tested with and how they should be applied.

Does the fixing method affect the warranty?

It can. A manufacturer's warranty is normally tied to a compliant installation, so fixing a tile in a way its installation guide does not allow is the quickest way to lose whatever cover remains.

Should I lay a test area first?

Yes, on any stock that has been in storage. Fix a small area with the method you have chosen, leave it in normal use for a few days, then lift a tile and look at both faces. It costs a morning and tells you more than any data sheet about how this stock behaves on this floor.